Elinchrom Elc Pro Hd 500 Single Flash Head

The Elinchrom ELC Pro HD 500 Flash Head from Elinchrom is evidence of the company's continued commitment to pushing the envelope in monolight design. Elinchrom has packed the ELC Pro HD 500 with professional features we've come to expect from a flash head of this calibre and added quite a bit more. Short recycling times coupled with fast flash durations make freeze-motion, stop-action shooting possible. In fact, up to 20 frames per second is possible at minimum power. An intelligent low noise, the temperature-activated fan keeps the head cool and lengthens the life of both the flash tube and modelling lamp. A pre-flash detector lets you integrate your on-camera flash into your studio system.

Power, variable continuously from 7 to 500Ws, can be mimicked by the 300W proportional modelling lamp to preview your effects. Although Elinchrom provides one, you can swap the sync cord with a separately purchased 8-channel transceiver for wireless triggering from your camera. The head has one built-in to receive the signal. Flash modes allow you to address special situations. The Sequential Mode enables triggering up to 20 ELCs in bursts or in a continuous cycle. Delayed Mode offers a choice of first or second curtain syncing while Strobo Mode allows single frame stroboscopic action sequences. Finally, the auto-sensing multi-voltage power supply means that you can use the ELC Pro HD 500 anywhere in the world.

• Built-in EL-Skyport receiver for triggering
• EL-Skyport with 8 frequency channels with 4 groups
• EL-Skyport Speed Sync mode for synchronization up to a 1/320 sec on enabled SLR cameras
• Intelligent pre-flash detector system to enable the use of ELC units with speedlights
• 8 f-stop range
• Action-freezing flash durations of 1/2330 @ full power (t0.5) and as short as 1/5000 sec at 53Ws
• Stable even at fastest recycling times
• Up to 20 flashes per second
• Consistent colour temperature with +/- 150K
• Power Auto-dump
• Multi-voltage auto-detection: 90-265 VAC excluding modelling lamp
• Low 5V sync voltage safe for all digital camera systems
• Intelligent low noise fan spins slower or faster depending on the internal temperature of the unit
• Impact-resistant and fire retardant body shell
• Accessory bayonet permits use of the complete range of light modifiers
• The Elinchrom Standard

The Elinchrom Standard

• OLED display for information and clarity
• Dashboard for an enhanced experience
• Precise control

Flash Modes

• Sequence Mode allows you to sequentially trigger up to 20 ELCs, in bursts or as a continuous cycle to utilize the high frame rate of your camera
• Delayed Mode provides the option of first or second curtain sync and everything in-between
• Strobo Mode allows you to take a picture with stroboscopic effects in a single frame

Elinchrom ELC 500 Flash Head Includes:

• 1x Elinchrom ELC Pro HD 500Ws Flash Head
• 1x Mains Cable
• 1x Sync Cable
• 1x Modeling Lamp (300W)
• 1x Glass Dome
• 1x Protective Cap
• 2x 16cm Reflectors
• 1x Limited 2-Year Warranty
• 2x Mains Cable
• 1x Sync Cable
• 2x Modeling Lamp (300W)
• 2x Glass Dome
• 2x Protective Cap
• 2x 16cm Reflectors
• 1x Elinchrom Skyport SPEED Transmitter
• 1x Elinchrom ProTec Poly Bag
• 1x Limited 2-Year Warranty

Compatibility

Elinchrom Elc Pro Hd 500 Single Flash Head

Features

• 500Ws Flash Unit
• Recycling Full Power: 0.7 Sec @ 115VAC
• 8 Stop Flash Variability
• 90 - 265VAC, 50/60Hz
• Sequence, Delay and Strobo Modes
• Integrated 8-Channel Transceiver
• Temperature Controlled Fan Cooling
• 300W Modeling Lamp
• Up to 20 fps at Minimum Power
• Includes Reflector