PocketWizard FlexTT5-Nikon Transceiver (433MHz)

$363.00
Use the FlexTT5 Transceiver with the MiniTT1 Transmitter to control single or multiple off-camera electronic or intelligent i-TTL / CLS Speedlights.
SKU: PocketWizard FlexTT5-Nikon Transceiver (433MHz)
 

Accessories

Product Description

PocketWizard’s newest firmware platform taps into the camera’s digital communications to enable an entirely new level of remote flash capability through our proven radio system. ControlTL allows remote i-TTL for Nikon CLS / i-TTL systems as well as Manual Power Control.  ControlTL firmware is configurable and upgradeable for “future-proof” continuous improvement. 

Locking your FlexTT5 Transceiver into the hot shoe of a Nikon DSLR camera, and mounting CLS / i-TTL flashes onto FlexTT5 Transceivers gives you full flash exposure control with the freedom and reliability of a PocketWizard radio. There are no special settings to make or modes to call up.  Use the camera’s exposure compensation controls for basic control of remote flashes, or add an AC3 ZoneController or Nikon Master unit for even more flexibility.

Adjust the manual power settings of your remote Nikon Speedlights directly from a SB-800, SB-900 flash or PocketWizard AC3 ZoneController mounted on your on-camera FlexTT5.  Working with a Nikon SB-800, SB-900 or AC3 in the shoe of the FlexTT5, you can independently control the power output of up to three remote groups of lights (you can have as many lights in each group as you want) from full power down to the lowest setting.   Now you can work with total control with your remote lights, without leaving your shooting position.  Nikon SU-800 Wireless Speedlight Commander may also be used.

The FlexTT5 Transceiver has an A-B-C zone select switch to allow use with the remote groups/zones found on on the PocketWizard AC3 ZoneController or Nikon flashes. Zones allow you to control single or groups of lights independently from other lights in different zones. These zones can also be used with a MultiMAX thus allowing you to pair a single MultiMAX radio on camera with FlexTT5's Transceivers on your remote flashes and utilize many of the MultiMAX's advance trigger functions.

Our patent pending HyperSync technology allows photographers to achieve faster X-sync speeds, sometimes up to 1/8000 of a second, with full power flash.  Now you can cut the ambient light and use wide-open apertures, outdoors in bright sunlight.  HyperSync automatically adjusts the timing of your flash trigger so that faster than X-sync speeds can be achieved.  With certain Nikon camera and flash combinations, you can achieve sync all the way to 1/8000th of a second.  Just imagine what you can do using flash in bright sun with wide open apertures and fast shutter speeds.  Since HyperSync is a trigger function you can use any PocketWizard Receiver including the FlexTT5, PlusX, Plus III, Plus II or MultiMAX.  HyperSync works optimally with Studio flash. See High Speed Sync (Auto FP) below for higher than XSync speeds with Speedlights,

HyperSync Automation adjusts HyperSync timing in two separate places – on the transmitter and on the receiving ControlTL radio. The transmitting or on-camera MiniTT1 or FlexTT5 automatically adjusts HyperSync to compensate for changes made to shutter speed. Photographers can further refine HyperSync via the PocketWizard Utility.  For more information on Configuring HyperSync Automation, visit the HyperSync section of the PocketWizard Wiki.

 

Specifications

TTL Compatibility:

Nikon i-TTL

Frequency:

340.00 - 354.00 MHz US FCC / IC
433.42 - 434.42 MHz CE

Channels:

52 Channels over 26 Frequencies (FCC/IC)
35 Channels over 5 Frequencies (CE)

Antenna:

2.7" (6.9 cm) rubberized with 180 degree swing

Transmit output power:

Less than 0.001 watt (1/1000 of a watt or 1 milliwatt)

Range Performance:

Up to 10 to 240 meters (30 to 800 feet) for E-TTL II triggering.  Up to 10 to 365 meters (30 to 1200 feet) for basic triggering. Range is dependent on multiple factors including equipment, mode, environment, positioning, orientation and interference.

Mounting:

Hot Shoe, 1/4-20, lanyard, velcro

Maximum Shooting Rate  Frames per second (fps)

TTL Mode:  within 1 FPS of camera's maximum FPS
Basic Trigger Mode: Camera Max FPS
* dependent on flash power settings 
FPS = Frames Per Second

Power / Channel Switch

OFF - C.2 - C.1

Zone Select Switch

A-B-C (matches Nikon zones)

Status Indicator

LED: Green, Amber, Red status indications

Camera / P1 Port

1/8" (3.5 mm) stereo miniphone for 2-stage remote camera triggering.  Port Voltage Handling: up to 50 Volts, 100 milliamp continuous
Tip = Trigger
Ring = Pre-Trigger
Sleeve = Ground

Flash / P2 Port

1/8" (3.5 mm) mono miniphone.  Port Voltage Handling: up to 200 Volts, 4 amps peak, 250 milliamp continuous, non-polarized

Minimum Receive Contact Time

Camera / P1 Port = 80 milliseconds

 Flash / P2 Port = 500us

Voltage Present

3.3 VDC (all pins) - safe for all cameras

Hot Shoe voltage protection:

Hot Shoe: up to 50V

USB:

USB Compliant 2.0, Mini-B Connector, 5VDC regulated, 100mA, Pin 1 Positive, Pin 4 Ground

Operating Temperature

Above -15° C (5° F) and below 50° C (120° F).

Storage Temperature (without battery)

Above -30 C (-22 F) and below 85 C (185 F)

Construction

High impact plastic, captive battery door
Hot Shoe made of glass reinforced resin

Power

Two (2) AA (IEC:LR6) Alkaline recommended, other chemistries (NiMH, NiCAD, Lithium) allowed, USB

Battery Life

60 + Hours 

Dimensions

3.6" (9.2 cm) long x 2.9" (7.3 cm) wide x 1.4" (3.6 cm) tall, antenna lowered

Weight

5.4 oz (153 grams) 3.8 oz (108 grams) without batteries

Included in the box

FlexTT5 Transceiver, USB cable, Two (2) AA batteries, Quick Guide

ROHS Compliant

 

Additional information

Specifications No
What's in the box No
Brand No
Lens Mount No
Sensor Size No
Cart button text No

Warranty

Manufacturer Warranty

Reviews